archive
archive valves
archive
archive valves
6N14P tube: datasheets and technical data
Explore available pinout, electrical data and related types for the 6N14P vacuum tube.
The 6N14P, or 6Н14П, is a miniature twin triode with separate cathodes for high-frequency amplification. Preserved texts describe cascode use in VHF receivers, and the bilingual sheet includes curves specifically for that connection. The two systems thus operate in one stage according to circuit voltages and bias. Our sources relate it to the ECC84, 6CW7 and 6L16; these relationships do not remove the need to check pin connections, supplies and limits before replacement. It has a glass envelope, indirectly heated oxide cathodes and a nine-pin noval base.
The first triode has its cathode on pin 1, grid on 2 and anode on 3; the grid also connects to the internal screen. The heater is on 4 and 5. In the second triode, the grid is on 6, cathode on pins 7 and 8, and anode on 9. The bilingual sheet specifies a 6.3 V, 350 ±30 mA heater; at 90 V anode voltage with a 125 Ω self-bias cathode resistor, it gives each triode 10.5 ±3 mA current, 6.8 ±1.5 mA/V transconductance and an amplification factor of 25 ±7. Equivalent noise resistance is 0.6 kΩ. An accompanying sheet gives 10 mA per triode and specifies two 125 Ω resistors: that document’s data remain distinct from the table with tolerances.
The sections do not have identical capacitances. The bilingual sheet gives grid-to-cathode capacitance of 4.7 ±1 pF for the first triode and 2.55 ±0.55 pF for the second; anode-to-cathode values are respectively 2.8 ±0.5 and 1.15 ±0.25 pF. Maximum grid-to-anode capacitances are 0.25 and 1.8 pF. Second-triode input resistance is specified at 200 MHz, not 20 MHz as in a secondary transcription. The accompanying sheet gives 1.7 kΩ at 200 MHz. Bilingual-document curves distinguish individual-section characteristics from cascode characteristics, including second-system grid currents. The annotated technical excerpt flags its anode graph as belonging to another tube: it is not used to derive 6N14P values.
Documented limits include 300 V anode voltage, 1.5 W anode dissipation and 1 MΩ in the grid circuit. The 470 V rating applies only with the tube cut off and anode current no greater than 5 µA. The accompanying sheet permits 90 V with the heater positive relative to the cathode and 180 V with the heater negative; it also recommends avoiding series heater connection and prohibits simultaneous operation at two or more limiting values. The bilingual document gives 5.7–6.9 V heater voltage and states a 1500-hour guaranteed life, applying to the type under source conditions. Its drawing gives 56.5 mm maximum overall height, whereas the accompanying sheet gives 57 mm; both list 22.5 mm maximum diameter and 15 g maximum mass.
Tube images
Pinout and connections
Base: Noval (B9A)
Electrical data
Heater
- Heater voltage Vh
- 6.3 V
- Heater current Ih
- 0.35 A
Datasheet PDF
EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34
How to use the Valve Archive
EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.
Datasheet PDF and frequent searches
The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.