archive
archive valves
archive
archive valves
7C6 tube: datasheets and technical data
Explore available pinout, electrical data and related types for the 7C6 vacuum tube.
The 7C6 combines two diodes and a high-amplification-factor triode in one loctal envelope. Tung-Sol specifies detection and high-gain audio amplification with a low-drain heater. In receivers this combination supports signal detection, control circuits and audio amplification. Sylvania compares its characteristics with type 75 except for heater ratings; electrical similarity does not remove socket and wiring differences.
The T-9 glass envelope has an eight-contact base, diagram 8W. Heater pins 1 and 8, triode anode 2, grid 3; diode anodes 5 and 6. The common cathode connects to both 4 and 7: Sylvania explains that pin 4 also supports the cathode internally, so both contacts have the same potential. No top cap is required and any mounting position is allowed. Operating heater data are 6.3 V and 0.15 A AC or DC, distinct from historical nominal 7 V and 0.160 A.
To characterize the triode, Sylvania and Tung-Sol give 1 mA at 100 V anode and zero grid, about 0.1 MΩ internal resistance, 850 µmho transconductance and amplification factor 85. At 250 V anode and −1 V grid the figures are 1.3 mA, again about 0.1 MΩ, 1000 µmho and factor 100. Sylvania explicitly warns these are reference values rather than operating points with an anode-load resistor. Triode µ must not be confused with actual circuit gain.
Sylvania advises against fixed bias for the triode, requiring a high grid resistance and essentially zero-bias operation. For a 250 V anode supply it suggests about 0.25 MΩ anode load; RCA’s 1940 sheet also specifies a 10 MΩ grid resistor and states that diode biasing of the triode is unsuitable. These notes explain the 7C6 circuit without turning the −1 V characterization point into a universal fixed-bias prescription.
Tung-Sol gives amplifier examples with 0.25 MΩ anode load and 10 MΩ grid resistor. With 100 V anode supply, stated gain is 38 or 42 and output 5 or 6 V RMS according to the following tube’s grid resistance; with 300 V supply the figures become 54 or 56 and 37 or 43 V RMS. Distortion is 5%. Brimar also documents RC coupling: at 250 V supply, 0.27 MΩ anode load, 10 MΩ grid resistor and 0.47 MΩ following load, it lists gain 57 and 39 V peak output at 5%. Brimar’s peak volts are not directly the same quantity as Tung-Sol’s RMS volts.
Sylvania and Tung-Sol give 300 V maximum anode, while RCA’s tentative April 15, 1940 sheet gives 250 V; the difference retains its document context. Sylvania also specifies 90 V heater-to-cathode and 1 mA maximum continuous current per diode anode, with maximum drop 10 V at 0.8 mA. For the triode RCA and Sylvania’s manual give 1.4 pF grid-to-anode, 2.4 pF grid-to-cathode and 3 pF anode-to-cathode. These data, bias notes and common cathode describe the 7C6 more precisely than its twin-diode-triode label alone.
Tube images
Pinout and connections
Base: Loctal 8-pin (B8G) (8 pin)
| Pin | Function |
|---|---|
| 1 | h |
| 2 | a |
| 3 | g1 |
| 4 | k |
| 5 | a(d2) |
| 6 | a(d1) |
| 7 | k |
| 8 | h |
Electrical data
Heater
- Heater voltage Vh
- 6.3 V
- Heater current Ih
- 0.15 A
Interelectrode capacitances
- Grid-to-cathode capacitance Cgk
- 2.4 pF
- Anode-to-cathode capacitance Cak
- 2.4 pF
- Grid-to-anode capacitance Cga
- 1.6 pF
Substitutes
Datasheet PDF
EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34
How to use the Valve Archive
EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.
Datasheet PDF and frequent searches
The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.