archive
archive valves
archive
archive valves
ECC99 tube: datasheets and technical data
Explore available pinout, electrical data and related types for the ECC99 vacuum tube.
The JJ Electronic ECC99 is a modern twin triode with a noval base, particularly relevant to driver and audio stages requiring relatively high plate current. Although the data-sheet heading describes it as a radio-frequency twin triode, recommended applications include driving power triodes such as the 300B and 2A3, headphone output stages, preamplifiers and small push-pull triode amplifiers. The manufacturer also mentions shunt-regulated power supplies and a 10 W output-stage example using four ECC99 tubes: this power belongs to that configuration, not to a single tube.
Both sheets give a typical operating point of 150 V plate voltage and −4 V grid voltage, with 18 mA plate current. Transconductance is 9.5 mA/V, internal resistance 2.3 kΩ and amplification factor 22. These values describe a specific operating point; the plate and transfer curves show how current changes with plate voltage and bias. The value of μ alone does not represent the gain of a complete stage, which depends on the circuit and load.
The centre-tapped heater can operate at 6.3 V and 800 mA or 12.6 V and 400 mA. The pin assignment places the plate, grid and cathode of one section on pins 1, 2 and 3, and those of the other on 6, 7 and 8; pins 4 and 5 are the heater ends and pin 9 is the centre tap. The drawings specify a maximum diameter of 22 mm, a 62.2 mm envelope height and 68.4 mm overall height. The two systems sharing the envelope also have separately specified internal capacitances.
The two available JJ versions agree on limits of 400 V plate voltage, 60 mA cathode current and 200 V between cathode and heater, but differ in plate dissipation: the two-page sheet states 3.5 W, while the catalogue page gives 5 W. No documented chronology allows the higher figure to be applied indiscriminately to every specimen. Their capacitance values are identical: 5.8 pF grid-to-cathode and 5.1 pF grid-to-plate for each section; plate capacitance is 0.91 pF for the first system and 0.81 pF for the second.
A manufacturer note mentions use in place of the 5687, E182CC, 6840 and 6BL7, but explicitly warns that some of these tubes may have different connections. This qualification accompanies the application statement and prevents it from being read as automatic replacement in the same socket. The ECC99 therefore offers several possibilities for drivers and small audio output stages, to be assessed through pin assignment, heater supply, operating point and the applicable data-sheet version.
Tube images
Pinout and connections
Base: Noval (B9A) (9 pin)
| Pin | Function |
|---|---|
| 1 | a(1) |
| 2 | g1(1) |
| 3 | k(1) |
| 4 | h |
| 5 | h |
| 6 | a(2) |
| 7 | g1(2) |
| 8 | k(2) |
| 9 | hct |
- The number 99 was reserved for miniature tubes with a seven-pin B7G base. JJ Electronic did not follow this convention when naming the ECC99 twin triode, introduced in the late 1990s.
Electrical data
Heater
- Heater voltage Vh
- 12.6 V
- Heater current Ih
- 0.4 A
Datasheet PDF
EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34
How to use the Valve Archive
EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.
Datasheet PDF and frequent searches
The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.