archive
archive valves
archive
archive valves
EF72 tube: datasheets and technical data
Explore available pinout, electrical data and related types for the EF72 vacuum tube.
The EF72 is a subminiature high-transconductance RF pentode, indirectly heated at 6.3 V, 150 mA. Our sources describe its use in the input stage of communications receivers; Mullard Issue 3 documents both normal pentode and triode connections. Photographs of Mullard specimens show the small glass body, connecting wires and internal construction visible through anode openings. One specimen also shows the strap joining the two anode halves: a construction detail enriching the description of this compact radio valve.
As a pentode, with anode and screen at 100 V and grid at −1.4 V, Mullard gives 7 mA anode current, 2.2 mA screen current, 5 mA/V transconductance and 250 kΩ internal resistance. Input resistance listed at 50 MHz is 25 kΩ. As a triode, with 100 V anode and the same bias, listed current is 9.2 mA, transconductance 6.8 mA/V, internal resistance 5.3 kΩ and amplification factor 36. The fuller eight-page booklet includes current, transconductance and impedance curves for both configurations: these figures describe different connections and should not be combined as characteristics of one circuit.
Pentode capacitances with and without an external shield are respectively 4.1 and 4 pF input, 2.5 and 2 pF output, and less than 0.015 and 0.02 pF anode-grid. Triode figures are 2.8 pF input, 4.2 pF output and 1.65 pF anode-grid. Mullard's limits are 175 V operating anode and screen, distinct from 300 V supplies, 800 mW anode dissipation, 300 mW screen and 1 W combined, with 12 mA maximum cathode current. Maximums of 500 kΩ grid-to-cathode, 20 kΩ heater-to-cathode and 100 V between the latter are also specified.
B8D/F uses eight wires: 1 control grid, 2, 4 and 8 cathode with suppressor and internal shield, 3 and 6 heater, 5 anode and 7 screen grid. The drawing gives 9.3–10.16 mm diameter and maximum bulb height of 38.1 mm excluding wires, with any mounting position permitted. Soldering must be at least 5 mm from the seal and bending at least 1.5 mm. Mullard warns that the valve can become very hot and recommends adequate cooling: a metal clip conducting heat to the chassis should produce about 100 °C bulb temperature. These are concrete instructions for understanding and preserving how this construction was intended to operate.
Tube images
Pinout and connections
Base: Subminiature 8-pin (B8D) (8 pin)
| Pin | Function |
|---|---|
| 1 | g1 |
| 2 | k,g3 |
| 3 | h |
| 4 | k,g3 |
| 5 | a |
| 6 | h |
| 7 | g2 |
| 8 | k,g3 |
Electrical data
Heater
- Heater voltage Vh
- 6.3 V
- Heater current Ih
- 0.15 A
Datasheet PDF
| Language | Pages | Manufacturer | |
|---|---|---|---|
| EF72.pdf | en | 2 | Mullard Radio Company Australia Ltd. |
| EF72.pdf | en | 8 |
EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34
How to use the Valve Archive
EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.
Datasheet PDF and frequent searches
The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.