archive
archive valves
archive
archive valves
EL50 tube: datasheets and technical data
Explore available pinout, electrical data and related types for the EL50 vacuum tube.
The EL50 is an indirectly heated power pentode developed expressly for push-pull audio output stages. Philips studies it mainly as a pair in class AB, discussing power, bias and supply in detail. The heater requires 6.3 V and 1.35 A, with AC parallel supply in the consulted sheets. The base has side contacts, while the anode connects to the top of the bulb. The Philips drawing gives maximum dimensions of 51 mm diameter and 135 mm height. The preserved images also show a specimen marked 10E/131; this identifies the specimen and does not promise interchangeability.
The Miniwatt sheet dated 12 March 1941 gives two separate static operating points. At 400 V anode, 425 V screen and −33 V control grid, anode current is 45 mA, screen current 5.5 mA, transconductance 6 mA/V and internal resistance 30 kΩ. At 800 V anode, 400 V screen and −37 V grid, these become 22.5 mA, 2.5 mA, 4 mA/V and 50 kΩ respectively. The third grid is at 0 V in both cases. These are single-valve measurement conditions, distinct from the pair's dynamic data and the output transformer's load resistance.
For a pair at 400 V anode and 425 V screen, Philips compares two arrangements. Self-bias with a shared 315 Ω cathode resistor and 9 kΩ anode-to-anode load gives a stated maximum output of 30 W at 10% total distortion. Fixed bias of −35 V with a 5 kΩ load gives 50 W at 3.4% distortion. Both require 25 V RMS drive per grid. In the latter case, anode currents rise from 2 × 25 mA at idle to 2 × 95 mA at maximum output, while screen currents rise from 2 × 2.5 to 2 × 22 mA. The article's powers are developed by the valves; transformer losses reduce the power reaching the loudspeaker.
The application article also explains why raising voltage does not simply increase the self-biased result. Average current changes the voltage across the cathode resistor and thus the operating point during the signal. In the 30 W example, distortion is approximately 2.6% at 27 W, rising rapidly to 10% at 30 W with a pronounced fifth harmonic. Too little initial bias would instead exceed idle anode dissipation. This is an observation about the described circuit, encouraging careful reading of maximum output rather than treating it as uniform performance at every listening level.
At higher voltage, the pair reaches 84 W at 6.6% distortion with 800 V anodes, 400 V screens, fixed bias of −37.5 V and a 16 kΩ load; drive is 23 V RMS per grid. Screen stability is decisive: in the example using a simple divider drawing 40 mA, voltage sag under signal can limit output to 50 W. The article instead proposes four series-connected 13201 stabilisers fed through 8 kΩ, maintaining approximately 380 V screens and allowing 80 W. The supply also matters: in the 400 V example, 200 Ω total supply resistance causes a 40 V drop for a 200 mA current increase, reducing the theoretical 50 W to 36 W. The pages discuss an AX50 gas rectifier with a filter without an input reservoir capacitor, and two DCG2/500 rectifiers for the 800 V stage; these are historical design examples under precise conditions.
The 1941 sheet's limits include 800 V operating anode voltage, 18 W anode dissipation and 120 mA cathode current. The separately listed 22 W is a test dissipation. Screen limits are 425 V, 3 W without signal and 10 W at maximum output; zero-current limits of 1600 V anode and 1000 V screen remain distinct from operating values. Maximum grid resistance is 0.7 MΩ for self-bias and 0.5 MΩ for fixed bias. Edition differences must also be preserved: the 1941 sheet gives 100 V heater-to-cathode and 5 kΩ resistance between them, whereas sheets dated 15 September 1948 give 50 V and 20 kΩ respectively. Anode-to-control-grid capacitance is below 0.8 pF. Curves, circuits and these different limit sets make the EL50 a well-documented audio output valve whose supply and bias concretely determine performance.
Tube images
Pinout and connections
Base: Side contact 8 (SC8) (8 pin)
| Pin | Function |
|---|---|
| 1 | tc |
| 2 | nc |
| 3 | h |
| 4 | h |
| 5 | k |
| 6 | g3 |
| 7 | g1 |
| 8 | g2 |
Electrical data
Heater
- Heater voltage Vh
- 6.3 V
- Heater current Ih
- 1.35 A
Datasheet PDF
EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34
How to use the Valve Archive
EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.
Datasheet PDF and frequent searches
The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.