archive

archive valves

6FG6 tube: datasheets and technical data

Explore available pinout, electrical data and related types for the 6FG6 vacuum tube.

2 PDF datasheets available

The 6FG6 is a bar-type luminous indicator with an incorporated amplifier triode. Rogers specifies tuning indication or modulation control; RCA publishes a sheet with the dual designation EM84/6FG6. The triode receives the control voltage, while the ray-control electrode changes the dark portion of the fluorescent target. It is not simply a lamp varying only in brightness: the curves describe dark-gap length.

Both consulted primary sheets specify a 6.3 V, 0.27 A heater, AC or DC. The typical circuit connects the ray-control electrode to the triode plate, supplies plate circuit and target at 250 V, and uses a 470 kΩ series plate resistor with 3 MΩ grid resistance. As grid supply changes from 0 to −22 V, the dark gap decreases from 0.83 ± 0.20 inches, or 21.082 ± 5.08 mm, to zero. The negative sign and measurement of the dark portion are essential to interpreting the response.

In that example, plate/ray-control branch current changes from 0.45 to 0.06 mA, while target current changes from 1.1 to 1.6 mA. Rogers gives a nonlinear dark-gap versus grid-voltage curve. RCA also distinguishes zero grid resistance: at zero grid supply the dark gap is then 0.94 ± 0.20 inches. Grid resistance is therefore part of the application conditions and must accompany comparisons of indication.

Design-center limits include maximum cathode current 3 mA, triode plate dissipation 0.5 W, grid-circuit resistance 3 MΩ, peak heater-cathode voltage 100 V in either polarity and bulb temperature 120 °C. Target and ray-control limits distinguish 550 V without current from 300 V with current; the target also has a 150 V lower limit in the specified operation. Thus 550 V is not a normal operating voltage to substitute for the example’s 250 V.

The base is Noval B9A, E9-1, RCA arrangement 9GA: 1 triode grid, 3 cathode, 4 and 5 heater, 6 fluorescent target, 7 ray-control electrode, 9 triode plate. Pins 2 and 8 have internal connections and RCA says not to use them as circuit tie points. The target lies on the inner glass surface above pin 7, helping orient the viewing window during installation.

For EM84/6FG6 RCA gives maximum overall length 2 27/32 inches = 72.23125 mm, maximum seated height 2 13/32 inches = 61.11875 mm, and diameter range 19.05–22.225 mm in the drawing’s specified zone. Body length excluding tip is 2 7/32 ± 3/32 inches = 56.35625 ± 2.38125 mm, distinct from overall height. Bulb T-6½, any mounting position. Documentation: Rogers Electronic Tubes & Components, 6FG6, sheets dated 16 October 1958 reproduced with reference to JEDEC release 2382 dated 9 February 1959; RCA Electron Tube Division, EM84/6FG6 Electron-Ray Tube, August 1959, drawings 92CS-10177 and 92CM-10179 and circuit CE-10174.

Pinout and connections

Base: Noval (B9A)

Electrical data

Heater

Heater voltage Vh
6.3 V
Heater current Ih
0.21 A

Other available variants

Datasheet PDF

PDF Language Pages Manufacturer
6FG6.pdf 3
6FG6.pdf en 3 Rogers-Majestic

EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34

74,001 Valvole ricercabili sul sito
18,704 Datasheet PDF disponibili

How to use the Valve Archive

EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.

Datasheet PDF and frequent searches

The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.