archive
archive valves
archive
archive valves
ECC91 tube: datasheets and technical data
Explore available pinout, electrical data and related types for the ECC91 vacuum tube.
The ECC91 is a miniature twin triode with a common cathode, documented chiefly for radio-frequency power amplifiers and oscillators. Philips and Mullard present it for VHF work; an RFT sheet also labels it 6J6 and describes mixer circuits. The envelope uses a seven-pin B7G miniature base and a 6.3 V, 450 mA heater. The common cathode is essential to its internal arrangement: the grids and plates are separate, while the cathode connection is shared. The second designation on the RFT sheet belongs to that document's context and does not by itself establish interchangeability in every piece of equipment.
Observations of preserved specimens show how this structure can be made: a central cathode, grids acting on only one side and plates on either side. In one specimen, the grid wire appears to have been wound first and then removed from half the assembly, leaving the portion facing the cathode; other specimens differ in plate shape and openness, from an open box to a single plate. These are details observed on those tubes, not a required description of every ECC91 ever made.
As a characterisation point for each section, Philips and an early Mullard sheet specify 100 V on the plate, 8.5 mA plate current and a 100 Ω cathode resistor: transconductance 5.3 mA/V, amplification factor 38 and internal resistance 7.1 kΩ. The 1961 Mullard sheet gives another point at 100 V, with −0.9 V on the grid, 9.0 mA, 5.6 mA/V and 6.8 kΩ. The two sets of figures belong to different documents and conditions; neither replaces the RF circuit tables, which also specify frequency, bias and load.
One Philips example, also given by Mullard, uses the two sections in push-pull as a class C RF telegraphy amplifier at 80 MHz. With 150 V on the plates, −10 V on the grids, 15 mA plate current and 8 mA grid current per section, and 0.35 W drive, the table specifies 3.5 W output. Bias may come from a fixed source or from grid or cathode current: Mullard gives 625 Ω in the grid path and 220 Ω at the cathode for the respective solutions, not as parts that must automatically be combined. Another example is a push-pull oscillator at 250 MHz: with 150 V on the plates and a common 2 kΩ grid resistor, it gives about 1 W output.
A later Mullard sheet adds a table spanning 50 to 250 MHz: in its class C amplifier example at 150 V and −10 V on the grids, stated output falls from 1.56 W at 50 MHz to 0.92 W at 250 MHz. Over the same range the frequency trebler is a separate test, with −100 V on the grids and lower output figures. RFT also proposes mixer use; its example at 150 V specifies an 800 Ω cathode resistor, 4.8 mA plate current, 1.9 mA/V conversion transconductance, a 0.5 MΩ grid resistor and 3.0 V RMS oscillator voltage. These are different circuits, not one common operating point.
The sources do not give identical limits. Philips and Mullard state a maximum operating plate voltage of 300 V and plate dissipation of 1.5 W per section; RFT gives 330 V and 1.6 W respectively. The 1961 Mullard sheet lists 250 MHz as a maximum frequency under its reference conditions, whereas RFT describes oscillator and mixer circuits up to approximately 600 MHz. Each figure should be attributed to its own sheet, particularly when assessing a specific circuit. Documentary sources: ECC91 data sheets from Philips, Mullard and RFT / VEB Werk für Fernmeldewesen.
Tube images
Pinout and connections
Base: Miniature 7-pin (B7G) (7 pin)
| Pin | Function |
|---|---|
| 1 | a(2) |
| 2 | a(1) |
| 3 | h |
| 4 | h |
| 5 | g(1) |
| 6 | g(2) |
| 7 | k |
Electrical data
Heater
- Heater voltage Vh
- 6.3 V
- Heater current Ih
- 0.45 A
Substitutes
Different ratings
Datasheet PDF
EL84 ECC83 12AX7 EL34 6L6GC 300B KT88 GZ34
How to use the Valve Archive
EnryLab Valve Archive allows you to search for PDF datasheets and technical documentation by entering the exact code of a vacuum tube. Enter codes such as EL84, ECC83, 12AX7, 6L6GC, or 300B to view variants, manufacturers, and documents available in the technical archive. The search uses exact matches, thus avoiding partial or irrelevant results and making it easier to find the correct datasheet.
Datasheet PDF and frequent searches
The most searched acronyms have dedicated and indexable pages, with clean URLs and linked documentation. You can start with frequent searches to quickly consult the most used valves in the audio, radio, and technical restoration fields.